Jump to content

This Week s Top Stories Concerning Audi G28

From WikiHikmah

How to Replace an audi key G28 Engine Speed Sensor

In this video Charles the humble mechanic demonstrates how to replace the G28 engine speed sensor. The sensor is situated on the edge of the transmission just above the flywheel ring gear. It transmits a signal to the ECU via the grey wire (T55/49) and then to the tachometer within the instrument cluster.

1. Engine Speed Sensor

The grey wire is located on the edge of transmission, just above the flywheel ring. This sensor sends signals through the grey wire to pin T55/49. The ECU then utilizes this information to regulate the boost, fuel, and timig. It also sends signals to the G5 tachometer inside the instrument cluster.

The sensor is used to correlate with the G40 Camshaft position Sensor. The ecu must be aware of when the crankshaft has reached TDC and also where the camshaft lies so that it can activate the spark and injectors.

If this sensor fails the ECU will display an error code P00160 which indicates that the Crank Shaft and Intake Camshaft are not in sync, possibly indicating chain stretch or a jumped link on the upper timing chain. The code won't show without the additional information provided by other sensors (G4 or G40).

It is a little tricky to test since there are several pins on the connector and each has its own functions. The best method for doing this is by measuring the resistance between the ECU and the sensor. If the sensor is operational, it should read about 1000 ohms. If you are having problems with this part, check for evidence of coolant or oil in the connector bay.

2. Injectors

Yesterday accelerating full speed from highway paytoll, i experienced a big cut in power like the engine is running out of gas or injectors aren't firing any more. I pulled out the spark plugs this morning, three were soaked with gasoline and the fourth was unclean. I put a piece of tissue over each injector hole and when I start the engine without sparks, the three with gazoline jump out. The 4th one stays shut. I tested the ground connection on ECU pins 14/55/30/55/48/55/14/55/48/ I get zero ohm. Therefore, i think the issue is elsewhere.

I also tried to reset the PID without success. The car can start when the G28 is not plugged in and runs fine when it is connected, but still has the intermittent misfire issue at higher RPM. The coolant sensor (G62), even if it is not plugged in, shows a temperature of -49c. Also, i noticed that the oil pressure gauge in the cockpit is showing 2 bar while the actual pressure is 0.0 when I crank up the engine.

I'm not sure what to do. I think I've eliminated everything else. I'm concerned that i may have missed something. If anyone has suggestions, please let me know! TIA!

3. Fuel Pump

The fuel pump of the g28 receives signals from the RPM sensor. The GM-style sender is the same as the G4 and both are used in the 80, 100, 200, UrS and RS2 cars so you can easily find one at a junkyard or from a parts store. Testing them is easy by putting your DMM in resistance mode and take measurements between pins 1 (with the bump on the connector's side up) and 2 (2nd from left on the black connector's end). They should be infinite Ohms.

4. ECU

Our 20vt turbo (3B AAN, ABY and ADU) engines have an ECU that has to know the speed and position of the crankshaft in order to make decisions about fuel injector timing etc. To do this, it uses a Crank Position Sensor (G4) and an Engine Speed Sensor (G28). If either of these sensors go wrong, you will receive codes on the diagnostic scanner that can lead to engine shutdown.

A damaged G28 sensor could cause an inaccurate gearbox speed counter and a gearbox which shifts more quickly than normal, or a misfire in gear. If you have any of these problems, it is most likely that your sensor is deteriorating and should be replaced. The good news is that they are very cheap and easily accessible particularly when you're looking at a Bosch model, which is what ours are. Alternatively, GM's version of this part is a good option.

5. Tachometer

A failing engine speed sensor could be the reason behind many issues with your vehicle. It is a crucial part of your audi replacement key cost's transmission, as it sends information to the ECU about how the car's crankshaft is turning. This sensor can cause the transmission to fail and other components of the car to be affected.

The G5 engine speed sensor is located at the edge of the transmission, above the flywheel ring gear and sends a signal directly to the ECU at pin T55/49 through a grey wire. The ECU uses this signal to control the amount of fuel and boost, and also timig. It also relays it to the G5 Tachometer in instrument cluster. You can test for sensor failure by checking continuity from the sensor to the tachometer. Additionally, you can examine the continuity between pins T55/49 of the ECU and pin T6a/1 of the instrument cluster (trace [79]), and between pin T6a/1 and pin T26a/12. You should see approximately 1000 ohms of resistance between these two points. This part is common across the audi key copy New Key (Http://Bbs.161Forum.Com/Bbs/Home.Php?Mod=Space&Uid=341119) 80-100-200-RS2 series, starting from the 1985 MC up to the 1997 UrS An and 1995 RS2 DU You may also find them in wrecking yards.